Extruders, Downstream And Supply Inc

new and used plastics manufacturing equipment for the extrusion industry

2 Inch EDS Extruder

- 2 Inch screw diameter - 26:1 L/D ratio - With your choice of screw design - All screws have colmony 56 weld-on flite tips and double/high polish chrome (.002 Inches thick) is standard 

- Barrel has a cast-in bi-metallic lining extending throughout the 24:1 L/D ratio (a full 24 turns under heat) - screw has 26 turns when turns thru feed throat are included

- Barrel is divided into 3 Heat/Cool Zones - heating is via finned cast aluminium heater jackets and cooling is via a 565 cfm (closely shrouded to the heater/barrel) Dayton fan on each zone

- Heavy duty double reduction Rossi Gearbox @ 17:1 reduction giving 100 screw rpm @ 1750 motor rpm input and 1:1 sheave ratio.  Gearbox is rated at 85 hp which offers a 3.4 Service Factor when used with a 25 HP drive system

- Heavy duty thrust bearing with B-10 rating of 300,000 hrs at 5,000 psi and 100 screw rpm.  Thrust bearing is integral to gearbox allowing precise alignment and 50% immersion of bearing in gearbox oil - both offer extended like to the gearbox/thrut assembly

- Water cooled feed throat assembly - turned from a solid piece of tool steel.  This system offers superior strength and wear resistance over cast assemblies.  Actual opening of 2 1/2 Inch cut to the centerline of the screw

- Heavy gauge steel hopper with operator side sight glass and dump chute

- Drawer magnet between hopper and feed throat    

- Tapered barrel flange with 3 piece head clamp with single bolt closure - includes clamp, lifter and support

- Belt driven variable speed 25 HP ABB Or Westinghouse AC vector drive with marathon vector duty motor - Motor is totally enclosed and fan cooled.  Drive module is chasis mount and mounted in main control panel complete with start/stop buttons, digital screw RPM meter, digital motor amp load meter and 10 turn POT.  Motor is mounted on main base in a Z configuration with motor tucked under the gearbox.  This design creates a small footprint while allowing easy access for sheaves/belt maintenace or to modify screw speed range - machine is sheaved to 80 screw RPM unless otherwise advised

- Main control panel also houses electrical controls for barrel heating/cooling and drive functions.  The machine mounted over barrel main control panel consists of 3 barrel zones and 2 die zones - all controlled by RKC Mdl CB400 Auto-tune digital temperature control instruments.  Each zone will have ammeter indication of heater loading, branch fusing in addition to circuit breakers, mercury contactors for heater initiation (solid state can be subed at no charge) and solid state fan initiation

- Single point 460 Volt power connection thru door mounted disconnect

- (4) machinery mounting and leveling pads 

- 303 stainless steel breaker plate

- Panel mounted Dynisco digital pressure indicator with barrel mounted pressure transducer - wired for customer setable high pressure drive shutdown

- Swing gate assembly 

- Includes owner and installation manual with set of electrical drawings

- Painted your choice of colors with high temperature black motor and barrel covers

PRICE:   $34,500.00 US

Optional:  Extra die zone(s) - $850.00 each

Optional:  Hopper lid - $245.00

Optional:  Melt temperature indication added to above melt pressure indication - $195.00

          

2 1/2 Inch EDS Extruder

- 2 1/2 Inch screw diameter - 26:1 L/D ratio - With your choice of screw design - All screws have colmony 56 weld-on flite tips and double/high polish chrome (.002 Inches thick) is standard 

- Barrel has a cast-in bi-metallic lining extending throughout the 24:1 L/D ratio (a full 24 turns under heat) - screw has 26 turns when turns thru feed throat are included

- Barrel is divided into 4 Heat/Cool Zones - heating is via finned cast aluminium heater jackets and cooling is via a 565 cfm (closely shrouded to the heater/barrel) Dayton fan on each zone

- Heavy duty double reduction Rossi Gearbox @ 17:1 reduction giving 100 screw rpm @ 1750 motor rpm input and 1:1 sheave ratio.  Gearbox is rated at 118 hp which offers a 2.95 Service Factor when used with a 40 HP drive system

- Heavy duty thrust bearing with B-10 rating of 300,000 hrs at 5,000 psi and 100 screw rpm.  Thrust bearing is integral to gearbox allowing precise alignment and 50% immersion of bearing in gearbox oil - both offer extended like to the gearbox/thrut assembly

- Water cooled feed throat assembly - turned from a solid piece of tool steel.  This system offers superior strength and wear resistance over cast assemblies.  Actual opening of 3 1/2 Inch cut to the centerline of the screw

- Heavy gauge steel hopper with operator side sight glass and dump chute

- Drawer magnet between hopper and feed throat    

- Tapered barrel flange with 3 piece head clamp with single bolt closure - includes clamp, lifter and support

- Belt driven variable speed 40 HP ABB Or Westinghouse AC vector drive with marathon vector duty motor - Motor is totally enclosed and fan cooled.  Drive module is chasis mount and mounted in main control panel complete with start/stop buttons, digital screw RPM meter, digital motor amp load meter and 10 turn POT.  Motor is mounted on main base in a Z configuration with motor tucked under the gearbox.  This design creates a small footprint while allowing easy access for sheaves/belt maintenace or to modify screw speed range - machine is sheaved to 80 screw RPM unless otherwise advised

- Main control panel also houses electrical controls for barrel heating/cooling and drive functions.  The machine mounted over barrel main control panel consists of 4 barrel zones and 2 die zones - all controlled by RKC Mdl CB400 Auto-tune digital temperature control instruments.  Each zone will have ammeter indication of heater loading, branch fusing in addition to circuit breakers, mercury contactors for heater initiation (solid state can be subed at no charge) and solid state fan initiation

- Single point 460 Volt power connection thru door mounted disconnect

- (6) machinery mounting and leveling pads 

- 303 stainless steel breaker plate

- Panel mounted Dynisco digital pressure indicator with barrel mounted pressure transducer - wired for customer setable high pressure drive shutdown

- Swing gate assembly 

- Includes owner and installation manual with set of electrical drawings

- Painted your choice of colors with high temperature black motor and barrel covers

PRICE:   $49,500.00 US

Optional:  Extra die zone(s) - $850.00 each

Optional:  Hopper lid - $295.00

Optional:  Melt temperature indication added to above melt pressure indication - $195.00

 

 

 

 

3 Inch EDS Extruder

Inch screw diameter - 26:1 L/D ratio - With your choice of screw design - All screws have colmony 56 weld-on flite tips and double/high polish chrome (.002 Inches thick) is standard 

- Barrel has a cast-in bi-metallic lining extending throughout the 24:1 L/D ratio (a full 24 turns under heat) - screw has 26 turns when turns thru feed throat are included

- Barrel is divided into 5 Heat/Cool Zones - heating is via finned cast aluminium heater jackets and cooling is via a 565 cfm (closely shrouded to the heater/barrel) Dayton fan on each zone

- Heavy duty double reduction Rossi Gearbox @ 17:1 reduction giving 100 screw rpm @ 1750 motor rpm input and 1:1 sheave ratio.  Gearbox is rated at 148 hp which offers a 2.47 Service Factor when used with a 60 HP drive system

- Heavy duty thrust bearing with B-10 rating of 300,000 hrs at 5,000 psi and 100 screw rpm.  Thrust bearing is integral to gearbox allowing precise alignment and 50% immersion of bearing in gearbox oil - both offer extended like to the gearbox/thrut assembly

- Water cooled feed throat assembly - turned from a solid piece of tool steel.  This system offers superior strength and wear resistance over cast assemblies.  Actual opening of 3 1/2 Inch cut to the centerline of the screw

- Heavy gauge steel hopper with operator side sight glass and dump chute

- Drawer magnet between hopper and feed throat    

- Tapered barrel flange with 3 piece head clamp with single bolt closure - includes clamp, lifter and support

- Belt driven variable speed 60 HP ABB Or Westinghouse AC vector drive with marathon vector duty motor - Motor is totally enclosed and fan cooled.  Drive module is chasis mount and mounted in main control panel complete with start/stop buttons, digital screw RPM meter, digital motor amp load meter and 10 turn POT.  Motor is mounted on main base in a Z configuration with motor tucked under the gearbox.  This design creates a small footprint while allowing easy access for sheaves/belt maintenace or to modify screw speed range - machine is sheaved to 80 screw RPM unless otherwise advised

- Main control panel also houses electrical controls for barrel heating/cooling and drive functions.  The machine mounted over barrel main control panel consists of 5 barrel zones and 2 die zones - all controlled by RKC Mdl CB400 Auto-tune digital temperature control instruments.  Each zone will have ammeter indication of heater loading, branch fusing in addition to circuit breakers, mercury contactors for heater initiation (solid state can be subed at no charge) and solid state fan initiation

- Single point 460 Volt power connection thru door mounted disconnect

- (6) machinery mounting and leveling pads 

- 303 stainless steel breaker plate

- Panel mounted Dynisco digital pressure indicator with barrel mounted pressure transducer - wired for customer setable high pressure drive shutdown

- Swing gate assembly 

- Includes owner and installation manual with set of electrical drawings

- Painted your choice of colors with high temperature black motor and barrel covers

PRICE:   $59,500.00 US

Optional:  Extra die zone(s) - $850.00 each

Optional:  Hopper lid - $245.00

Optional:  Melt temperature indication added to above melt pressure indication - $195.00

 

 

 

3 1/2 Inch EDS Extruder

3 1/2 Inch screw diameter - 26:1 L/D ratio - With your choice of screw design - All screws have colmony 56 weld-on flite tips and double/high polish chrome (.002 Inches thick) is standard 

- Barrel has a cast-in bi-metallic lining extending throughout the 24:1 L/D ratio (a full 24 turns under heat) - screw has 26 turns when turns thru feed throat are included

- Barrel is divided into 5 Heat/Cool Zones - heating is via finned cast aluminium heater jackets and cooling is via a 985 cfm (closely shrouded to the heater/barrel) Dayton fan on each zone

- Heavy duty double reduction Rossi Gearbox @ 17:1 reduction giving 100 screw rpm @ 1750 motor rpm input and 1:1 sheave ratio.  Gearbox is rated at 258 hp which offers a 3.44 Service Factor when used with a 75 HP drive system

- Heavy duty thrust bearing with B-10 rating of 300,000 hrs at 5,000 psi and 100 screw rpm.  Thrust bearing is integral to gearbox allowing precise alignment and 50% immersion of bearing in gearbox oil - both offer extended like to the gearbox/thrut assembly

- Water cooled feed throat assembly - turned from a solid piece of tool steel.  This system offers superior strength and wear resistance over cast assemblies.  Actual opening of 4 1/2 Inch cut to the centerline of the screw

- Heavy gauge steel hopper with operator side sight glass and dump chute

- Drawer magnet between hopper and feed throat    

- Tapered barrel flange with 3 piece head clamp with single bolt closure - includes clamp, lifter and support

- Belt driven variable speed 75 HP ABB Or Westinghouse AC vector drive with marathon vector duty motor - Motor is totally enclosed and fan cooled.  Drive module is chasis mount and mounted in main control panel complete with start/stop buttons, digital screw RPM meter, digital motor amp load meter and 10 turn POT.  Motor is mounted on main base in a Z configuration with motor tucked under the gearbox.  This design creates a small footprint while allowing easy access for sheaves/belt maintenace or to modify screw speed range - machine is sheaved to 80 screw RPM unless otherwise advised

- Main control panel also houses electrical controls for barrel heating/cooling and drive functions.  The machine mounted over barrel main control panel consists of 5 barrel zones and 2 die zones - all controlled by RKC Mdl CB400 Auto-tune digital temperature control instruments.  Each zone will have ammeter indication of heater loading, branch fusing in addition to circuit breakers, mercury contactors for heater initiation (solid state can be subed at no charge) and solid state fan initiation

- Single point 460 Volt power connection thru door mounted disconnect

- (8) machinery mounting and leveling pads 

- 303 stainless steel breaker plate

- Panel mounted Dynisco digital pressure indicator with barrel mounted pressure transducer - wired for customer setable high pressure drive shutdown

- Swing gate assembly 

- Includes owner and installation manual with set of electrical drawings

- Painted your choice of colors with high temperature black motor and barrel covers

PRICE:   $69,500.00 US

Optional:  Extra die zone(s) - $850.00 each

Optional:  Hopper lid - $245.00

Optional:  Melt temperature indication added to above melt pressure indication - $95.00

 

 

 

 

 

4 1/2 Inch EDS Extruder

- 2 Inch screw diameter - 26:1 L/D ratio - With your choice of screw design - All screws have colmony 56 weld-on flite tips and double/high polish chrome (.002 Inches thick) is standard 

- Barrel has a cast-in bi-metallic lining extending throughout the 24:1 L/D ratio (a full 24 turns under heat) - screw has 26 turns when turns thru feed throat are included

- Barrel is divided into 5 Heat/Cool Zones - heating is via finned cast aluminium heater jackets and cooling is via a 985 cfm (closely shrouded to the heater/barrel) Dayton fan on each zone

- Heavy duty double reduction Rossi Gearbox @ 17:1 reduction giving 100 screw rpm @ 1750 motor rpm input and 1:1 sheave ratio.  Gearbox is rated at 389 hp which offers a 2.59 Service Factor when used with a 150 HP drive system

- Heavy duty thrust bearing with B-10 rating of 300,000 hrs at 5,000 psi and 100 screw rpm.  Thrust bearing is integral to gearbox allowing precise alignment and 50% immersion of bearing in gearbox oil - both offer extended like to the gearbox/thrut assembly

- Water cooled feed throat assembly - turned from a solid piece of tool steel.  This system offers superior strength and wear resistance over cast assemblies.  Actual opening of 6 Inch cut to the centerline of the screw

- Heavy gauge steel hopper with operator side sight glass and dump chute

- Drawer magnet between hopper and feed throat    

- Tapered barrel flange with 3 piece head clamp with single bolt closure - includes clamp, lifter and support

- Belt driven variable speed 150 HP ABB Or Westinghouse AC vector drive with marathon vector duty motor - Motor is totally enclosed and fan cooled.  Drive module is chasis mount and mounted in main control panel complete with start/stop buttons, digital screw RPM meter, digital motor amp load meter and 10 turn POT.  Motor is mounted on main base in a Z configuration with motor tucked under the gearbox.  This design creates a small footprint while allowing easy access for sheaves/belt maintenace or to modify screw speed range - machine is sheaved to 80 screw RPM unless otherwise advised

- Main control panel also houses electrical controls for barrel heating/cooling and drive functions.  The machine mounted over barrel main control panel consists of 5 barrel zones and 2 die zones - all controlled by RKC Mdl CB400 Auto-tune digital temperature control instruments.  Each zone will have ammeter indication of heater loading, branch fusing in addition to circuit breakers, mercury contactors for heater initiation (solid state can be subed at no charge) and solid state fan initiation

- Single point 460 Volt power connection thru door mounted disconnect

- (8) machinery mounting and leveling pads 

- 303 stainless steel breaker plate

- Panel mounted Dynisco digital pressure indicator with barrel mounted pressure transducer - wired for customer setable high pressure drive shutdown

- Swing gate assembly 

- Includes owner and installation manual with set of electrical drawings

- Painted your choice of colors with high temperature black motor and barrel covers

PRICE:   $94,500.00 US

Optional:  Extra die zone(s) - $850.00 each

Optional:  Hopper lid - $345.00

Optional:  Melt temperature indication added to above melt pressure indication - $195.00